buildwiz.uk
Part H

Approved Document H: Drainage and Waste Disposal

Building regulations governing drainage and waste disposal in England. Specifies waste pipe gradients (18–90mm fall per metre for 40mm pipes), trap requirements, foul drainage construction (granular bedding to BS EN 1610), and the four-step priority hierarchy for surface-water discharge (soakaway, watercourse, surface water sewer, combined sewer). Building control inspects drainage runs and connections against Part H before backfill.

Read on gov.uk All Approved Documents

Also known as

Part HApproved Document HAD HBuilding Regs Part HDrainage and Waste Disposalapproved-document-hH4Approved Document H4Part H4

What Part H requires for a home project

The Part H requirements and terms the buildwiz guides rely on, with paragraph references where the document gives one. Check the current edition on gov.uk before you build to it.

Limits and figures

110 mm soil pipe horizontal gradient absolute minimum
Shallow-end limit of the practical gradient range for 110 mm above-ground horizontal soil and waste runs. Below this fall, flow velocity drops below the self-cleansing threshold and solids deposit in the pipe. Approved Document H allows shallower 1:80 (12.5 mm/m) underground only where peak flow exceeds 1 L/s with a WC contributing; that exception does not apply to most above-ground branches inside an extension.
110 mm soil pipe horizontal gradient practical maximum
Steep-end limit of the practical gradient range for 110 mm above-ground horizontal soil and waste runs. Steeper than this, water separates from solids in the discharge: water outruns the load and leaves solids stranded in the pipe. Approved Document H Table 2 sets 18 to 90mm per metre for an unventilated WC branch; the no-maximum rule applies only to below-ground drains (Table 6).
32mm waste pipe maximum unvented run length
Maximum unvented branch run for a 32mm waste pipe under Approved Document H. Used for small hand basins; tighter limit than 40mm because the smaller bore draws down the trap seal faster.
40mm waste pipe maximum fall per metre
Maximum gradient for a 40mm domestic waste pipe under Approved Document H. A steeper fall lets water run off ahead of solids, depositing debris and creating a progressive blockage. Paired with the 18mm/m minimum to define the working band for 40mm wastes.
40mm waste pipe maximum unvented run length
Maximum unvented branch run for a 40mm waste pipe under Approved Document H. Longer runs siphon the trap seal and require either an anti-siphon trap, a vent connection, or an air admittance valve.
40mm waste pipe minimum fall per metre
Minimum gradient for a 40mm domestic waste pipe under Approved Document H. A shallower fall lets solids settle and the pipe blocks. Typically cited as the lower end of the 18-90mm/m working range for 40mm sink and basin wastes.
Air admittance valve minimum height above highest water entry
Minimum vertical clearance between an air admittance valve (AAV) and the highest connected branch on the soil stack it serves. The figure is a maker's instruction (for example FloPlast: 110mm valves fitted vertically at least 200mm above the highest branch connection; small branch valves have lower figures), not a figure in Approved Document H or BS EN 12380. The AAV must also be installed vertically and remain accessible for replacement.
Bath trap water seal minimum depth (space-constrained fixtures)
Minimum water seal depth for a bath or shower trap under Approved Document H Table 1: 50mm, against 75mm for basins, sinks, washing machines and dishwashers. WC pans are also 50mm. Where a bath or shower discharges directly to a gully, the seal may be reduced to not less than 38mm. Shallow bath traps are built to fit the 50mm seal into the space under a bath.
Drainage air-test hold duration
Duration for which the drainage system must hold pressure during the building control air test (Approved Document H para 2.60). The system is first pumped to 110mm water gauge and held for about 5 minutes to settle, then from an initial 100mm it must not lose more than 25mm over a 7-minute hold.
Drainage inspection chamber maximum spacing
Approved Document H Table 13 limit from the start of an external drain to its first inspection chamber, and from a shallow inspection chamber to a junction or small access fitting. Between shallow inspection chambers, and from a rodding eye to a chamber, the limit is 45m. Building control will check access spacing at the drainage inspection stage.
Drainage junction rodding access maximum distance
Approved Document H Table 13 sets 12m as the maximum distance from a small access fitting to a junction, and from the start of an external drain to a small or large access fitting. From a rodding eye or a shallow inspection chamber to a junction the limit is 22m. Ensures any blockage can be cleared without excavation.
Drainage pipe: minimum pea-gravel bedding cover above pipe crown
Minimum cover of single-size 10 mm or 20 mm pea gravel (or equivalent Type 6N/6P granular surround) above the crown of a buried plastic (PVC-U or PPs) drainage pipe before compacted hardcore or site fill is placed and compacted with a plate compactor. Approved Document H and the Building Regulations drainage guidance treat this bedding-and-surround detail as the engineered protection that isolates a flexible drain from point loads and vibration. With 150 mm of clean pea gravel above the crown, a standard domestic plate compactor's vibration dissipates through the gravel before reaching the pipe, and wheel loads spread over a safe bearing area. Without that bedding, the pipe can deform under compaction or under later traffic loads. Clay pipes need the same surround plus a flexible joint strategy, and should never be compacted directly with a wacker plate. Measure bedding depth before backfill: once the trench is closed, the inspector has no evidence of adequate cover.
Foul drain conditional shallow gradient (WC + full flow)
Approved Document H permits a 110mm foul drain to be laid at 1:80 (12.5mm fall per metre) only where peak flow exceeds 1 litre per second AND at least one WC discharges into the run. A typical kitchen-only rear extension meets neither condition, so the 1:40 self-cleansing minimum applies instead. Accept 1:80 only if your drainage layout includes a WC and the flow calculation is in the building regs submission.
Foul drain extreme shallow-end gradient limit
Not an Approved Document H figure: Table 6 gives 1:40 and 1:80 for 100mm foul drains and 1:150 for 150mm drains serving at least five WCs. Quoted by some drainage designers as a shallow-end limit (~9mm fall per metre) for 110mm drains. Workable only with substantial flow loading (multiple WCs and high-volume appliances) such that the drain self-cleanses by hydraulic flushing rather than gravity velocity. Effectively never seen on a single-storey domestic extension: included here so you recognise the figure if a drainage designer quotes it.
Foul drainage pipe minimum gradient
Minimum fall for a 100/110mm foul drain carrying a peak flow under 1 litre per second: 1 in 40 (25mm fall per metre run). Below this, flow velocity drops below the self-cleansing minimum and solids accumulate. Approved Document H sets no maximum gradient.
Foul waste pipe: minimum fall
Minimum fall (gradient) for small-bore foul waste pipework (32–50 mm diameter) serving basins, sinks, showers and baths, per BS EN 12056-2 and Approved Document H. Typical acceptable fall is 18 mm per metre (1:60) with a working window of roughly 1:110 to 1:40 for branch discharge pipes. Too shallow and solids and grease settle out; too steep and water outpaces the solids, again leading to blockages. For 100 mm soil stacks and main drains the standard fall is typically 1:40 to 1:80 depending on flow load. The practical constraint on an extension is that the fall has to be achieved while keeping every joist penetration within the 0.25-joist-depth and 0.25–0.4-span permitted zone: plan the route before drilling a single hole.
Minimum offset for opposed connections larger than 65 mm on a stack
Opposed branch connections larger than 65 mm that do not have swept entries should be offset by at least 200 mm to prevent crossflow. Opposed connections of 65 mm or less without swept entries should be offset 110 mm on a 100 mm stack. This is the AD H rule that the graph value for boss distance below a WC branch appears to confuse.
Sanitary pipework air pressure test pass level
Minimum positive air pressure that above-ground sanitary (soil and waste) pipework should withstand for at least 3 minutes, with every trap keeping a water seal of at least 25mm (Approved Document H paragraph 1.38). Distinct from the below-ground drain air test, which starts from 100mm water gauge and allows no more than 25mm loss over 7 minutes (paragraph 2.60).
Shared drainage with air admittance valves: open vent thresholds
There is no Approved Document H rule that one in five stacks must be open. The BBA certificates for air admittance valves allow up to four dwellings (one to three storeys) fitted with AAVs on a shared drain with no extra drain ventilation; five to ten dwellings need an open vent at the head of the drain, and eleven to twenty at the head and mid-point. AAVs must not be the only ventilation to a septic tank or cesspool, and AD H paragraph 2.18 needs an open vent on any drain with an intercepting trap or liable to surcharge.
Shower trap minimum water seal depth
Minimum water seal depth for a shower trap discharging to a single-stack drainage system, set by Approved Document H Table 1. The shorter 50 mm seal (vs the 75 mm minimum for basins, sinks, washing machines, dishwashers and bidets) reflects the lower siphon risk on a shallow shower waste run. Below this depth, sewer gas can escape through the trap once the seal evaporates.
Sink-to-stack distance before the branch needs ventilating
Maximum unventilated 40mm waste-pipe run from a sink trap to the soil stack (Approved Document H Table 2 and Diagram 3). Beyond it the branch must be ventilated by a branch vent pipe, a ventilating stack or an air admittance valve (AAV) (AD H 1.20), or run in 50mm pipe, which is allowed up to 4m. Beyond this distance the trap seal can be siphoned out as larger waste flows pass, causing the gurgle-and-smell complaint. The AAV is fitted at the high point of the run, usually inside a base unit or boxed section.
Soakaway minimum distance from property boundary
Commonly used minimum distance from a soakaway to a property boundary, to stop saturated ground affecting a neighbouring property's foundations or garden. It is a building control and drainage-design convention, not a figure in Approved Document H (2015), which sets no boundary distance; check with your building control body.
Standard domestic soil stack diameter
Standard external diameter of the main vertical soil stack and underground foul drainage pipe for domestic extensions. All branch waste pipes (sink, basin, bath, WC) ultimately discharge into this 110mm main. Part H gradient and run-length rules are keyed to this standard diameter.
Trap water seal minimum depth on single-stack drainage
Minimum depth of water held in the U-bend of a fixture trap on a modern single-stack drainage system: the sustained seal that blocks sewer gas and drain smells from entering the room. Single-stack systems dominate UK housing since the 1970s, combining foul and waste into one stack, which pulls harder on trap seals as water passes. The 75mm depth is the Approved Document H minimum for washbasins, bidets, kitchen sinks, washing machines, and dishwashers on single-stack systems.
Waste pipe fall practical working range (40mm pipe)
Recommended practical fall gradient range for a 40mm domestic waste pipe. Distinct from the Approved Document H regulatory range (18–90mm/m): the upper regulatory limit of 90mm/m is technically permitted but in practice causes water to outrun solids and leave debris behind. Plumbers and BCOs work to a tighter 18–45mm/m envelope as best practice. Use this range when planning the layout; use the regulatory entity when discussing what the regs strictly permit.
Waste pipe gradient at which trap self-siphoning starts
Trade rule of thumb only, not an Approved Document H figure. Approved Document H allows unventilated 40mm sink and bath branches at falls up to about 90 mm/m within their maximum lengths; the steeper-fall self-siphonage limit mainly matters on 32mm basin wastes, where the allowed fall reduces as the branch gets longer. Where a branch exceeds the AD H limits, fit an air admittance valve or use a larger pipe.

Terms explained

Air admittance valve
A one-way valve admitting air into the drainage system to prevent siphonage of trap seals, used instead of extending a vent pipe through the roof.
Air test
A pressure test applied to drainage pipework to check for leaks. The pipe system is sealed and pressurised; any pressure drop indicates a leak that must be fixed. Approved Document H sets the formal test after the pipes are laid, haunched and backfilled: 110mm water gauge held for about 5 minutes, then from 100mm no more than 25mm loss in 7 minutes. Many BCOs also watch a test at the open-trench visit, before backfilling.
Bottle Gully
A trapped surface-water fitting set at ground level that receives a downpipe or yard drainage and connects to the underground drain. A removable bottle-shaped insert traps silt and provides a water seal against drain smells, and is easier to rod and clear than a back-inlet gully. Distinct from an inspection chamber or a channel drain.
Branch discharge pipe
The pipe that carries waste from one or more appliances to the soil stack. Approved Document H limits its length, size and fall, and a branch that exceeds the limits must be vented (branch ventilating pipe or air admittance valve) rather than necessarily replaced by a pump.
Channel drain
A surface water drainage channel installed flush with paving at the junction between a patio and the house wall. Required when a flush-threshold patio is needed next to bifold or sliding doors to intercept surface water before it reaches the wall, while maintaining DPC clearance.
Coarse Aggregate
The third component of a site-mixed concrete batch alongside cement and sharp sand. Used in standard concrete mixes (1:2:4, 1:2:3, 1:3:6). Purchased separately from sharp sand when batching on site. Distinct from all-in ballast, which is a pre-blended combined aggregate. Homeowners using a concrete mixer must understand the difference between sharp sand and coarse aggregate and how to proportion them.
Digital Spirit Level
An electronic spirit level that uses sensors to display angle in degrees on an LCD screen. Accurate to 0.1mm/m vs 0.5mm/m for quality bubble levels. Audio beep alerts allow hands-free use.
Dimensional units
The everyday dimensional notation on UK building drawings, quotes and delivery tickets: millimetres, centimetres and metres for length; square metres (m2) for area-priced work such as paint, plaster, tiling and flooring; cubic metres (m3) for volume-priced materials such as concrete, soil and skips; and falls or gradients written as mm per metre or as ratios (1:40, 1:80) for drainage runs and flat roofs.
Downpipe
The vertical pipe that takes water from the gutter outlet down to drainage at ground level, discharging to a gully, soakaway, or surface-water drain. Round or square uPVC to match the guttering, fixed to the wall with pipe clips and connected with offset bends (swan necks) around the eaves overhang.
Drain Test Kit
Equipment for conducting a pre-inspection drain air test: 110mm drain plug/bung, flexible hose, hand pump, and pressure gauge. Community forums recommend homeowners buy one (~£40 from Screwfix) and pre-test drainage before the BCO visit to catch and fix leaks before failing in front of the inspector.
Drainage
Below-ground products that route foul water to the existing sewer connection and surface water to a soakaway: inspection chambers, soakaway crates, geotextile membrane, push-fit fittings, and threshold channel drains. Building control inspects every joint before the trench backfills.
Drainage gradient
The slope of a drainage pipe that allows waste to flow by gravity. For 110mm domestic drainage serving a kitchen extension (no WC), the minimum gradient is 1:40 (Approved Document H Table 6), a drop of 25mm per metre. Shallower than that, solids settle and cause recurring blockages; Approved Document H sets no maximum gradient. A trade rule of thumb sometimes called Maguire's rule (pipe diameter divided by 2.5 gives the gradient denominator, so 100 / 2.5 = 40) is not an Approved Document H rule.
Geotextile membrane
A permeable fabric material that filters water while blocking soil particles. In soakaway construction, geotextile wraps around soakaway crates to allow water to permeate out while preventing soil fines from entering and gradually clogging the void space. Also used in French drains and as a separation layer under hardcore. Without geotextile, a soakaway will progressively lose capacity as soil infiltrates the crates.
Guttering
The channel clipped to the fascia that catches roof run-off and carries it to the downpipes. uPVC is standard on extensions in half-round, square, or ogee profiles, and the profile and outlet positions must match the existing house run. Sized to the roof area drained, with falls set towards the outlets.
Laminate worktop
Most affordable worktop option (£80-200/lm supply-only). Chipboard core with decorative laminate surface. Huge design range, easy to fit, but not heat-resistant and joiners are visible. Compact laminate variant enables undermount sinks.
Macerator
A small electric unit that grinds WC waste and pumps it through narrow-bore pipe to the soil stack, for a loft or basement ensuite that cannot reach a gravity drain. Approved Document G para 4.25 allows a macerator WC only where there is also access to a WC discharging directly to a gravity system, and the unit conforms to BS EN 12050-1 or -3; para 5.10 covers pumped washing appliances (BS EN 12050-2). Check the installation guide of the model you are quoted for fall, length and electrical requirements.
Magnetic Spirit Level
A spirit level with a magnetic base that grips onto metal pipes, angle irons, and steel frames without needing to be held. Used by plumbers for checking pipe falls and by electricians for aligning metal conduit.
Paving slabs
Primary hard landscaping material for post-extension patios and paths. Available in concrete (£15-55/m²), natural stone (£40-95/m²), and porcelain (£50-80/m²). Requires a compacted hardcore sub-base and sharp sand bed.
Pea gravel
Rounded 10mm gravel used as bedding and surround material for underground drainage pipes. Follow the drainage design and pipe manufacturer’s instructions for bed depth, side support and surround height. Approved Document H, paragraph 2.43 and Diagram 10, distinguishes flexible-pipe support from Class B rigid-pipe bedding; Class B is not the name for a full granular surround around a flexible PVC pipe. Suitable bedding distributes loads and supports the pipe.
Percolation test
A site test (the Approved Document H2 paras 1.34 to 1.38 procedure, which H3 para 3.28 points to for soakaways; BRE Digest 365 for larger areas) to determine whether ground conditions are suitable for a soakaway. A hole is dug, filled with water, and the drainage rate is timed. If the soil infiltration rate is below 1x10^-6 m/s, a soakaway is not viable and a different surface water disposal method must be used. Building control requires evidence of a passing percolation test before approving a soakaway.
Plastic inspection chamber
A pre-formed polypropylene chamber (typically 320mm or 450mm diameter) installed at junctions, direction changes, and intervals in a domestic drainage run to provide access for inspection, testing, and rodding. Supplied as a kit with base, riser sections, and cover. Has largely replaced traditional brick-built manholes for domestic drainage. Must have a removable cover and be accessible from ground level.
Sharp Sand
Coarse, angular sand used in concrete mixes and for floor screeds. Usually too harsh for general bricklaying mortar, where soft building sand is used instead.
Soakaway crate
Modular polypropylene plastic cubes stacked to form an underground soakaway chamber. Wrapped in geotextile membrane to prevent soil ingress while allowing water to permeate out into the surrounding soil. More durable, compact, and easier to install than traditional rubble-filled soakaways. Multiple units stacked to achieve the required storage volume based on the roof area draining to them.
Soil Pipe 110mm
110mm diameter PVC pipe for connecting toilets and carrying foul waste to the main drain. Also acts as the soil vent pipe (SVP), which must be ventilated, either by an open vent above the roofline or by an air admittance valve inside the building where Approved Document H (paragraph 1.33) allows. Push-fit ring-seal joints. Building control will inspect the drainage layout.
Solvent-weld fittings
Rigid plastic fittings joined with solvent cement to create permanent, leak-free connections for waste pipes. Should always be used for concealed waste pipe runs.
Solvent-Weld Waste Pipe (32mm/40mm)
Rigid plastic waste pipes in 32mm (basin waste) and 40mm (bath/shower/kitchen sink waste) diameters. Joined using solvent cement for a permanent, leak-free connection. Must be installed with correct fall (gradient) for waste to flow properly.
Strap-on boss
A saddle fitting that clamps onto a soil or waste pipe and provides a female socket for a branch waste pipe connection, avoiding the need to cut out a tee fitting.
Underground drainage fittings
The bends, junctions, reducers, couplers, and adaptors that connect lengths of 110mm uPVC underground drainage pipe. Includes 45-degree and 90-degree bends, Y-junctions, T-junctions, couplers, reducers, access pipes, and rodding eyes. Push-fit ring-seal connections are standard for domestic drainage. Every change of direction and every junction requires a fitting; fittings accumulate quickly on a complex drainage layout.
Washing machine standpipe
A vertical waste pipe with an open top into which a washing machine or dishwasher drain hose terminates; the air gap prevents backflow into the appliance.
Waste pipe fall
The gradient at which waste pipes must be installed. Approved Document H specifies 18-90mm/m for 40mm pipe, with a maximum 3m run before an AAV is needed.
Waste Traps
U-shaped or bottle-shaped fittings installed below sinks, basins, baths and showers. They hold a small amount of water that acts as a seal to prevent drain smells entering the room. P-traps for wall waste exits, S-traps for floor waste exits, bottle traps where space is limited.
Water test
The follow-up drainage test triggered by a failed air test. Per Approved Document H para 2.61: fill the system to a depth of at least 1m at the highest invert (and no more than 5m above the lowest), leave it to condition the pipe (one hour is generally sufficient), then hold the test pressure for 30 minutes by topping up: losses must not exceed 0.15 L/m² for pipelines only or 0.20 L/m² including manholes. A failed air test does not condemn the drain; the water test verifies leak severity and location.

Pages where Part H comes up

15 guides reference Part H, grouped by build phase.

Want the full picture?

The buildwiz build guides walk through a UK extension in sequence and link to Part H (and every other Approved Document) at the exact stage it bites. That is usually a more productive way to use this material than reading the document cover to cover.